According to the different components of refractory bricks, they can be divided into five categories, namely: silicon aluminum refractory bricks, alkaline refractory bricks, carbon containing refractory bricks, zirconium containing refractory bricks, and thermal insulation refractory bricks. Any stove is not built with just one type of refractory brick, it requires a combination of different refractory bricks to be used. Below is a detailed introduction to the components of these five categories of refractory bricks.
1. Silicon aluminum refractory bricks, it is reported that they are based on the AL2O3-SiO2 binary system phase diagram as the basic theory, mainly including the following types.
(1) Silica brick refers to refractory bricks containing more than 293% SiO, and is the main variety of acidic refractory bricks. It is mainly used for building coke ovens, as well as for the arch roofs and other load-bearing parts of various thermal kilns for glass, ceramics, carbon calcination furnaces, and refractory bricks. It is also used in the high-temperature load-bearing parts of hot blast stoves, but it is not suitable for use in thermal equipment with temperature fluctuations below 600 ℃.
(2) Clay bricks are mainly composed of mullite (25% to 50%), glass phase (25% to 60%), and quartz and quartz (up to 30%). Usually, hard clay is used as raw material, pre calcined mature material, and then mixed with soft clay to form clay brick products using semi dry or plastic methods, with a temperature of 1300-1400 ° C. It is also possible to add a small amount of binders such as water glass and cement to make non burning products and amorphous materials. It is a commonly used refractory brick in blast furnaces, hot blast stoves, heating furnaces, power boilers, lime kilns, rotary kilns, ceramic and refractory brick firing kilns.
(3) High alumina refractory bricks have a mineral composition of corundum, mullite, and glass phase, and their content depends on the AL2O3/SiO2 ratio and the type and quantity of impurities. The grade of refractory bricks can be classified according to the AL2O3 content. The raw materials are natural ores such as high alumina bauxite and sillimanite, as well as those mixed with fused alumina, sintered alumina, synthetic mullite, and clinker calcined with alumina and clay in different proportions. It is mostly produced by sintering method. But there are also products such as cast bricks, melted grain bricks, unburned bricks, and unshaped refractory bricks. High alumina refractory bricks are widely used in the steel industry, non-ferrous metal industry, and other industries.
(4) Corundum refractory brick refers to a type of refractory brick with an AL2O3 content of not less than 90% and mainly composed of corundum. It can be divided into sintered corundum brick and fused corundum brick.
2. Alkaline series refractory bricks. Alkaline refractory bricks refer to refractory products mainly composed of alkaline oxides such as Mg0 and CaO. The main varieties are as follows.
(1) Magnesia refractory brick refers to a refractory brick made of magnesia as raw material, with periclase as the main crystal phase and MgO content of 80% to 85% or more. Its products are divided into two categories: metallurgical magnesia and magnesium products. According to different chemical compositions and uses, there are Martin sand, ordinary metallurgical magnesia sand, ordinary magnesia brick, magnesia silica brick, magnesia alumina brick, magnesia calcium brick, magnesia carbon brick, and other varieties. Magnesia refractory brick is the most important product in alkaline refractory bricks, with high refractoriness and good resistance to alkaline slag and iron slag. It is an important high-grade refractory brick. Mainly used for open hearth furnaces, oxygen converters, electric furnaces, and non-ferrous metal smelting.
(2) Baiyun stone brick is an alkaline refractory brick produced mainly from dolomite. Widely used in alkaline converters, it can also be used as an inner lining for certain refining packages outside the furnace.
(3) Magnesium olivine refractory brick is a type of refractory brick mainly composed of 2MgO · SiO2 magnesium olivine. It is mainly used for grid bricks in open hearth heat storage chambers, bricks for casting ingots, heating furnace bottoms, and also has good application effects in copper smelting furnaces.
3. Carbon containing refractory bricks. Carbon containing refractory bricks refer to refractory brick products made of carbon or carbon compounds, with different forms of carbon as the main component. They are mainly divided into the following categories.
(1) Carbon brick is a high-temperature resistant neutral refractory brick product made mainly from carbonaceous materials and added with an appropriate amount of binder. Carbon bricks are widely used for building the bottom, hearth, belly, and lower part of blast furnaces. It can improve the continuous operation time of the blast furnace and extend its service life. In addition, carbon bricks are widely used in the electrochemical industry, chemical industry, petrochemical industry, electroplating industry, ferroalloy industrial furnaces (or equipment linings), acid and alkali tank linings and pipelines, as well as furnace linings for melting non-ferrous metals such as lead, aluminum, tin, etc.
(2) Graphite refractory products are refractory materials made from natural graphite as raw material and clay as binder. This type of product includes graphite clay crucibles, distillation tanks, plug bricks for cast steel, spout bricks, and lining bricks for steel barrels. The graphite clay crucible with the highest production and widest application is used for steelmaking and melting non-ferrous metals.
(3) Silicon carbide refractory products are advanced refractory materials produced from silicon carbide (SiC) as raw material. It has good wear resistance and corrosion resistance, high temperature strength, high thermal conductivity, low coefficient of linear expansion, and good thermal shock resistance. In the field of steel smelting, it can be used for lining steel drums, nozzles, plugs, blast furnace bottoms and belly, tapping troughs, converter and electric furnace tapping ports, and heating furnaces without water-cooled sliding rails. In the smelting of non-ferrous metals (zinc, copper, aluminum, etc.), it is widely used in stills, distillation tower trays, electrolytic cell sidewalls, molten metal pipelines, suction pumps, and melting metal crucibles. In the silicate industry, it is widely used as a shed board and flame insulation material for various kilns, such as muffle furnace lining and box bowls. In the chemical industry, it is commonly used in oil and gas generators, organic waste calcination furnaces, petroleum gasifiers, and desulfurization furnaces. In addition, it can be used as a rocket nozzle and high-temperature gas turbine blade in space technology.
4. Zirconium containing refractory bricks. Belonging to an acidic material, it is a product made from natural zircon sand (ZrSiO2) as raw material. Zirconium refractory bricks are different from silicon aluminum refractory bricks and carbon containing refractory bricks. They have good slag resistance, low thermal expansion rate, decreased thermal conductivity with increasing temperature, high load softening temperature, high wear resistance, and good thermal shock resistance. They have become important materials in various industrial fields. With the development of continuous casting and vacuum degassing technology in the metallurgical industry, the application of zircon refractory bricks is becoming increasingly widespread, mainly classified into the following categories.
(1) Zirconia bricks are used in the steelmaking process through steel tapping and degassing. Zirconia refractory materials have good corrosion resistance and thermal shock resistance to slag and steel, and are suitable for working under reduced pressure. They are widely used in the metallurgical industry for lining degassing steel drums, stainless steel drums, continuous casting drums, casting mouth bricks, plug bricks, sleeve bricks, and high-temperature induction furnace linings. Zirconia refractory bricks have high resistance to acidic slag and glass, and are therefore widely used in severely damaged parts of glass kilns for melting the most active glass. Zirconia refractory materials also have the property of not being penetrated by metallic aluminum, aluminum oxides, and their slag, thus achieving good results on the bottom of aluminum smelting furnaces.
(2) AZS electric melting brick, also known as electric melting zirconia corundum brick, has become a necessary refractory material for key parts of glass kilns with the development of the glass industry. It has strong resistance to the erosion of glass liquid.
(3) AZS re sintered electric melting bricks are mainly used for masonry of thermal equipment such as the bottom, walls, and thermal storage grid bricks of glass tank furnaces.
(4) Zirconium mullite electric melting brick is characterized by a dense crystal structure, high load softening temperature, good thermal shock resistance, high mechanical strength at room and high temperatures, good wear resistance, good thermal conductivity, and excellent resistance to slag erosion. This product has a wide range of applications, including the discharge ports of metallurgical heating furnaces, homogenization furnaces, and calcium carbide furnaces, as well as the walls of glass melting furnaces, and has shown excellent performance.
5. Insulated refractory bricks. It refers to refractory materials with high porosity, low bulk density, and low thermal conductivity. Thermal insulation refractory materials, also known as lightweight refractory materials. It includes the following categories.
(1) High alumina insulated lightweight refractory brick. It is an insulated lightweight refractory brick mainly made of bauxite with an AL2O3 content of not less than 48%. The production process adopts foam method or burn out additive method. High alumina insulated lightweight refractory bricks can be used for laying insulation layers and areas without strong erosion and scouring effects from high-temperature molten materials. When in direct contact with flames, the surface contact temperature of typical high alumina insulated refractory bricks should not exceed 1350 ℃. Moli stone insulated refractory bricks can directly contact flames and have the characteristics of high temperature resistance, high strength, and significant energy-saving effect. Suitable for lining pyrolysis furnaces, hot air furnaces, ceramic roller kilns, electric porcelain drawer kilns, and various resistance furnaces.
(2) Clay insulation lightweight refractory brick is an insulation refractory brick made mainly from refractory clay with an AL2O3 content of 30% to 48%. Its production process adopts burn out addition method and foam method. Using refractory clay, floating beads, and refractory clay clinker as raw materials, mixed with binders and sawdust, after batching, mixing, molding, drying, and firing, a volumetric density of 0 Products with a density of 3-1.5g/cm3. The production of clay insulation bricks accounts for more than half of the total production of insulation refractory bricks.
The Chinese standard (GB 3994-1983) divides clay insulation bricks into 10 grades based on their bulk density: NG-1.5, NG-1.3a, NG-1.3b, NG-1.0, NG-0.9, NG-0.8, NG-0.7, NG-0.6, NG-0.5, and NG-0.4.
(3) Diatomaceous earth heat-insulating lightweight refractory brick is a heat-insulating refractory product made mainly from diatomaceous earth. It is mainly used for insulation layers below 900 ℃.
The Chinese standard (GB 3996-1983) divides diatomaceous earth insulation products into six grades based on their bulk density: GG-0.7a, GG-0.7b, GG-0.6, GG-0.5a, GG-0.5b, and GG-0.4.
(4) Float bead bricks are insulation and refractory products made mainly from float beads. Float beads are hollow silica alumina glass beads that are extracted by flotation from fly ash in thermal power plants. It is lightweight, thin walled, hollow, with a smooth surface, high temperature resistance, and good thermal insulation performance. By utilizing the excellent properties of floating beads, lightweight insulation refractory materials with excellent thermal insulation performance can be manufactured. The production of floating bead bricks can be achieved through semi dry molding.
Classification of refractory bricks
Aug 06, 2024
Leave a message
